Forkliftaction.com

DISCUSSION FORUMS : Forkliftaction.communicate

My forum profile

Printable version

Discussion Forums Home

Forum:

Technical arena

Discussion:

Linde R14 traction fault (computer program help)

Number of messages: 10

START MESSAGE:

Leon_W
Tyne & Wear, United Kingdom

What software is needed with the can box and cable to connect to a laptop for fault findind. I have an intermittent fault, after the handbrake has been released traction is slow, there is no mechanical fault to be found, the handbrake switch is ok, apparently when the fault is on the traction is very slow, unlike when the handbrake switch is actuated the speed is medium. I have the can box and lead but have no software.
Any help would be appricated. I think it is a 115 series.

Posted 16 Jul 2008 06:29 PM

Report this message

REPLIES:

Sort replies by

justinm
New York, United States

if it has the same box as the 324's then check the speed sensor and wring for it
324's slow down like that if the sensor doesnt report speed
i believe this uses the same system

-------------------------
New York, New York its a heluva town ..you know that The Bronx is up ..and im Brooklyn down

Posted 26 Jul 2008 09:45 PM

Report this message

richard_y
Singapore, Singapore

You have to use Linde software to check on the fault numbers. Linde software is not available unless you are the dealer. In the 115 series, even though the correct part had being changed, some parts need to go into "teach again" which means that the new values will be set.

Posted 1 Aug 2008 05:38 PM

Report this message

Leon_W
Tyne & Wear, United Kingdom

Thank you for your help so far. i have since found out it is series 113.

Posted 1 Aug 2008 07:00 PM

Report this message

jason_t
Hampshire, United Kingdom

See if the truck has wiring for a height limit switch on the mast. I had a similar fault a while ago, never had a switch, but the wiring was there.

Posted 8 Aug 2008 08:44 AM

Report this message

richard_y
Singapore, Singapore

series 113 do not use any software. Please check on your moving mast switch. If may be fouling some time sensing that the mast had been moved forward.

Posted 8 Aug 2008 11:52 PM

Report this message

sullyamg
West Midlands, United Kingdom

i believe on this truck the first stage of the parkbrake brings in slow (inching) speed it may be worth checking

Posted 16 Aug 2008 06:04 AM

Report this message

michel_v
noord holland, Netherlands

truckdocktor and cambox

Posted 22 Aug 2008 03:30 AM

Report this message

andy_n
Victoria, Australia

we have 2. no diagnostic tools. however found same problem to be improper brake adjustment on drive motor. important to lubricate brake arm pivot points and adjust brake so arms release evenly. also a wiggle of the park brake handle in the release position with button pressed in helps

Posted 31 Aug 2008 06:09 PM

Report this message

BIGBOY
zuid-holland, Netherlands

if the truck is an 113 with joysticks you can do an readout with the truckdoctor software and the normal connector which you would use for a 335 and336 truck.
give futher info and i can help you.

Posted 19 Sep 2008 07:25 AM

Report this message

Forkliftaction.com accepts no responsibility for forum content and requires forum participants to adhere to the rules. Click here for more information.

FORUM GLOSSARY

Click for description.

FORUM

DISCUSSION

MESSAGES

NICKNAME

SIGNATURE

FORUMS

Discuss: Industry News & Whispers

Discuss: Conferences, trade shows & other events

Discuss: Mechanical Troubleshooting

Discuss: Technical arena. Did you know? Who knows?

Discuss: Machines. Forklifts, stackers, telehandlers, container handlers and reach stackers

Discuss: Business issues

Discuss: Safety, training & legislation

Discuss: Fun at work